cisco 7200 simulation, dynamips,Dynagen,GNS3,PEMU,

I have started troubleshooting the connection from SW5 to the ETHSW1. The idea is to set up a trunk to ETHSW1 that branches off and connects to SW1 and R1. See the below configs. When I first boot up the lab, I can see these devices from my physical switch SW5:

SW5#show cdp nei
Capability Codes: R – Router, T – Trans Bridge, B – Source Route Bridge
S – Switch, H – Host, I – IGMP, r – Repeater, P – Phone

Device ID Local Intrfce Holdtme Capability Platform Port ID
SW6 Gig 0/1 143 S I WS-C3560G Gig 0/1
Rack1SW1 Gig 0/48 175 R S I 3640 Fas 1/2
Rack1R1 Gig 0/48 175 R S I 3640 Fas 2/0

What is strange is that I can “sorta” ping R1 from SW5:
SW5#ping 192.168.77.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.77.1, timeout is 2 seconds:
!….
Success rate is 20 percent (1/5), round-trip min/avg/max = 34/34/34 ms

However I cannot ping SW1 at all.

What is interesting is that I tried experimenting with the trunking on SW1 I received these errors:

Rack1SW1(config)#int fa1/2
Rack1SW1(config-if)#switchport mode trunk
Rack1SW1(config-if)#
*Mar 1 00:10:37.571: %DTP-5-TRUNKPORTON: Port Fa1/2 has become dot1q trunk
Rack1SW1(config-if)#exit
*Mar 1 00:10:37.967: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with
inconsistent peer vlan
id 88 on FastEthernet1/2 VLAN1.
*Mar 1 00:10:37.971: %SPANTREE-2-BLOCK_PVID_PEER: Blocking
FastEthernet1/2 on VLAN88. Inc
onsistent peer vlan.
*Mar 1 00:10:37.995: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking
FastEthernet1/2 on VLAN1. Inc
onsistent local vlan.

And I receive these errors on my physical switch:

SW5#
00:27:13: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent
peer vlan id 1 on GigabitEthernet0/48 VLAN88.
00:27:13: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/48
on VLAN0088. Inconsistent local vlan.
SW5#
00:27:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan88,
changed state to down
SW5#
00:27:28: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking
GigabitEthernet0/48 on VLAN0088. Port consistency restored.
SW5#
SW5#
SW5#
00:27:35: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent
peer vlan id 1 on GigabitEthernet0/48 VLAN88.
00:27:35: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/48
on VLAN0088. Inconsistent local vlan.

I’ve checked everything I can think of and I’m not sure what’s going on. I’ve even gone into my NIC card on my PC and made sure it was set to speed 100 and duplex full.

SW5 config:
Current configuration : 2436 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname SW5
!
!
no aaa new-model
system mtu routing 1500
ip subnet-zero
no ip domain-lookup
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
!
interface GigabitEthernet0/48
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2-4094
switchport mode trunk
speed 100
duplex full
!
!
interface Vlan1
no ip address
shutdown
!
interface Vlan77
ip address 192.168.77.2 255.255.255.252
!
interface Vlan88
ip address 192.168.88.2 255.255.255.252
!
ip classless
ip http server
!
!
control-plane
!
!
line con 0
exec-timeout 0 0
logging synchronous
line vty 0 4
login
line vty 5 15
login
!
end

——–

R1 config:

Rack1R1#show run
Building configuration…

Current configuration : 1363 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Rack1R1
!
boot-start-marker
boot-end-marker
!
enable password cisco
!
no aaa new-model
!
resource policy
!
memory-size iomem 5
!
!
ip cef
no ip domain lookup
!
!
interface Loopback0
ip address 150.1.1.1 255.255.255.0
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0
no ip address
encapsulation frame-relay
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/0.1 point-to-point
ip address 155.1.0.1 255.255.255.0
frame-relay interface-dlci 105
!
interface Serial1/1
ip address 155.1.13.1 255.255.255.0
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/2
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface Serial1/3
no ip address
shutdown
serial restart-delay 0
no dce-terminal-timing-enable
!
interface FastEthernet2/0
ip address 192.168.77.1 255.255.255.252
duplex auto
speed auto
!
ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
line vty 0 4
password cisco
login
!
!
end

SW1 config:

Rack1SW1#show run
Building configuration…

Current configuration : 1747 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Rack1SW1
!
boot-start-marker
boot-end-marker
!
enable password cisco
!
no aaa new-model
!
resource policy
!
memory-size iomem 5
!
!
ip cef
no ip domain lookup
!
!

!
!
!
vtp file nvram:vlan.dat

!
!
!
!
!
!
interface Loopback0
ip address 150.1.7.7 255.255.255.0
!
interface FastEthernet1/0
!
interface FastEthernet1/1
switchport access vlan 146
!
interface FastEthernet1/2
switchport access vlan 88
duplex half
speed 100
!
interface FastEthernet1/3
no switchport
ip address 155.1.37.7 255.255.255.0
!
interface FastEthernet1/4
!
interface FastEthernet1/5
switchport access vlan 58
!
interface FastEthernet1/6
!
interface FastEthernet1/7
switchport mode trunk
!
interface FastEthernet1/8
switchport mode trunk
!
interface FastEthernet1/9
switchport mode trunk
!
interface FastEthernet1/10
switchport mode trunk
!
interface FastEthernet1/11
switchport mode trunk
!
interface FastEthernet1/12
switchport mode trunk
!
interface FastEthernet1/13
switchport mode trunk
!
interface FastEthernet1/14
switchport mode trunk
!
interface FastEthernet1/15
switchport mode trunk
!
interface Vlan1
no ip address
!
interface Vlan7
ip address 155.1.7.7 255.255.255.0
!
interface Vlan67
ip address 155.1.67.7 255.255.255.0
!
interface Vlan79
ip address 155.1.79.7 255.255.255.0
!
interface Vlan88
ip address 192.168.88.1 255.255.255.252
!
ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
line vty 0 4
password cisco
login
line vty 5 15
password cisco
login
!
!
end

————-

Dynamips config:

##################################################
#
# Define global router parameters for instance 1
#
##################################################

autostart=false
[localhost:7200]

[[3640]]
image = C:\Program Files\Dynamips\images\c3640-ik9o3s-mz.124-7.BIN
ram = 96
disk0 = 0
disk1 = 0
idlepc = 0×60638cd8

#############
[[Router R1]]
#############
model = 3640
console = 2001
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4T
slot2 = NM-1FE-TX
F0/0 = SW1 F1/1
S1/0 = FRSW s1/0
F2/0 = ETHSW1 3

#############
[[Router R2]]
#############
model = 3640
console = 2002
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4T
F0/0 = SW2 F1/2
S1/0 = FRSW s1/1

#############
[[Router R3]]
#############
model = 3640
console = 2003
mmap = false
slot0 = NM-4E
slot1 = NM-4T
S1/0 = FRSW s1/2
S1/1 = FRSW s1/3
S1/2 = R1 S1/1
S1/3 = R2 S1/1
E0/0 = SW1 F1/3
E0/1 = SW3 F1/3

#############
[[Router R4]]
#############
model = 3640
console = 2004
mmap = false
slot0 = NM-4E
slot1 = NM-4T
E0/0 = SW2 F1/4
E0/1 = SW4 F1/4
S1/0 = FRSW s1/4
S1/1 = R5 S1/1

#############
[[Router R5]]
#############
model = 3640
console = 2005
mmap = false
slot0 = NM-4E
slot1 = NM-4T
E0/0 = SW1 F1/5
E0/1 = SW3 F1/5
S1/0 = FRSW s1/5

#############
[[Router R6]]
#############
model = 3640
console = 2006
mmap = false
slot0 = NM-1FE-TX
slot1 = NM-4T
F0/0 = SW2 F1/6
S1/0 = FRSW s1/6

##################################################
#
# Define global router parameters for instance 2
#
##################################################

autostart=false
[localhost:7201]
udp = 11000

[[3640]]
image = C:\Program Files\Dynamips\images\c3640-ik9o3s-mz.124-7.BIN
ram = 96
disk0 = 0
disk1 = 0
idlepc = 0×60638cd8

##############
[[Router SW1]]
##############
model = 3640
console = 2007
mmap = false
slot1 = NM-16ESW
F1/7 = SW2 F1/7
F1/8 = SW2 F1/8
F1/9 = SW2 F1/9
F1/10 = SW3 F1/7
F1/11 = SW3 F1/8
F1/12 = SW3 F1/9
F1/13 = SW4 F1/7
F1/14 = SW4 F1/8
F1/15 = SW4 F1/9
FA1/2 = ETHSW1 2

##############
[[Router SW2]]
##############
model = 3640
console = 2008
mmap = false
slot1 = NM-16ESW
F1/10 = SW3 F1/10
F1/11 = SW3 F1/11
F1/12 = SW3 F1/12
F1/13 = SW4 F1/10
F1/14 = SW4 F1/11
F1/15 = SW4 F1/12

##############
[[Router SW3]]
##############
model = 3640
console = 2009
mmap = false
slot1 = NM-16ESW
F1/13 = SW4 F1/13
F1/14 = SW4 F1/14
F1/15 = SW4 F1/15

##############
[[Router SW4]]
##############
model = 3640
console = 2010
mmap = false
slot1 = NM-16ESW

##################################################
#
# Define global router parameters for instance 3
#
##################################################

autostart=false
[localhost:7202]
udp = 12000

[[3640]]
image = C:\Program Files\Dynamips\images\c3640-ik9o3s-mz.124-7.BIN
ram = 96
disk0 = 0
disk1 = 0
idlepc = 0×606398e8

[[7200]]
image = C:\Program Files\Dynamips\images\c7200-jk9o3s-mz.123-18.BIN
ram = 96
disk0 = 0
disk1 = 0
idlepc = 0×60750bf0
npe = npe-400

##############
[[Router BB1]]
##############
model = 3640
console = 2011
mmap = false
slot1 = NM-4T
S1/0 = BB3 S1/0
S1/1 = FRSW s1/7

##############
[[Router BB2]]
##############
model = 3640
console = 2012
mmap = false
slot0 = NM-4E
E0/0 = SW2 F1/0

##############
[[Router BB3]]
##############
model = 3640
console = 2013
mmap = false
slot0 = NM-4E
slot1 = NM-4T
E0/0 = SW3 F1/0

##############
[[Router FRSW]]
##############
model = 7200
console = 2014
mmap = false
slot1= PA-8T